Clopay Torsion Spring Replacement Nationwide | Otto’s Garage Door

Clopay Torsion Spring Replacement: The McKinney Owner’s Guide

We stock and install Clopay-compatible torsion springs throughout McKinney, and a replacement typically runs $180-$340 installed, with most jobs done same day. You’ll usually know the spring failed because you heard a bang in the garage that sounded like a car backfiring, then found the door dead on the tracks or sitting crooked when you tried to open it. That’s the torsion spring letting go, and it’s not a part anyone should ignore or try to shortcut. We’re an independent shop, not affiliated with Clopay, but we’ve matched their springs to their doors since before the Toll Brothers started putting up the newer sections of Craig Ranch.

Call (945) 777-4688

Which Clopay Models This Applies To

Clopay builds doors across a bunch of lines, and the torsion spring spec follows the door’s weight and height, not just the series name. We work on everything from the entry-level Classic series through the mid-grade Gallery and Premium lines, plus the heavier commercial-style doors on a lot of the larger homes out toward Melissa and Princeton.

The real gotcha with Clopay is that the factory label on the door or the end bearing plate will sometimes list a generic spring code rather than a true size. If the original spring was already replaced once, or if the door has an add-on like a strut or insulation kit that changed its weight, the “correct” spring from a catalog won’t balance right. That’s exactly the kind of thing you’d never know from an online lookup. Cheap aftermarket springs with the same wire diameter but a lower cycle rating are another thing we see in McKinney: they’ll work for a year, then the door nudges out of balance and eats the opener gear because the springs settled faster than the other side. Clopay’s OEM springs are rated for their cycle count, but a quality equivalent engineered to match the door’s actual weight and drum is just as good when selected properly. We carry both.

Signs Your Clopay Torsion Spring Replacement Is Failing

• The door feels heavy when you lift it by hand. That means the spring has lost tension and the opener is now doing all the work. It’s a 200-pound door; the opener is not supposed to carry it.
• You see a visible gap in the spring coil. A healthy torsion spring is continuous. If there’s a clean break or a stretched-looking spot where the coil separated, the spring is done and needs to go now.
• The door opens a few inches and stops. The spring can’t provide the counterbalance, so the opener’s force sensor trips. People assume it’s the opener. It’s almost never the opener.
• You hear a loud bang from the garage, then the door won’t move. That’s the spring snapping under tension. It’s the most common way McKinney homeowners find out, and it usually happens in the early morning when the garage is cold.
• Cables are loose or dangling off the drums. When the spring fails, the cables lose tension and can slide off the drum. Running the opener after this will yank a cable through the track or bend a panel.

Replacement Cost & What’s Included

A Clopay torsion spring replacement in McKinney runs $180-$340 installed. Here’s what that covers:

• Spring pair replacement: $110-$210 for the springs themselves, matched to the door’s weight and the cycle rating you want
• Labor and balancing: $70-$130, including removing old springs, installing new ones, setting tension, and lubricating the system
• Parts we typically replace at the same time: center bearing, end bearings, or cable drum if they show wear (added to the quote before we touch anything)

The price is quoted on the call and held at your driveway. If the door needs a spring plus a cable or two because the snap took a cable with it, that’s the cable repair range of $130-$250 added on top, and you’ll hear the number before we start. Every Clopay spring we install carries our 90-Day Done Right Promise. If something’s off, one call brings us back, no runaround.

DIY or Call Us?

Here’s my honest split. You can safely check a few things yourself: look for a break in the spring, see if cables are loose, and look at whether the door hangs crooked when you lift it by hand. That’s all useful info for the phone call. What you should not do is put a wrench on a torsion spring. The tension on a wound spring is enough to take a finger off or worse if the winding bar slips, and I have seen a homeowner lose teeth that way. It’s not about protecting our work; it’s about keeping you out of the hospital. If you want someone who will match the spring to the door and set it right the first time, call (945) 777-4688 and we’ll get it done.

FAQs